#1. P/N: AM03-009042A | Part name: Assy Cover-Dt Vp Top Cover Sub Assy | Qty: 1 | Old P/N: AM03-006021A #2. P/N: FC15-001584B | Part name: Cover-Dt Vp Top Cover Center | Qty: 1 | Old P/N: FC15-001073A FC15-001584A #3. P/N: FC09-002933B | Part name: Bracket-Dt Cover Bkt Y | Qty: 2 | Old P/N: […]
Category Archives: SMT Machines MRO
03
Dec
Dec
#16. P/N: N610041187AA | Part name: Head Camera:NPM | Qty: 1 #17. P/N: N610052706AB | Part name: LED Lighting Unit:NPM | Qty: 1 #18. P/N: N610161110AA | Part name: Head Option Driving Unit:NPM-D3 | Qty: 1 #19. P/N: N610160758AA | Part name: Whole Cover:NPM-D3 | Qty: 1 #20. P/N: N610162273AA | Part name: Label(Whole Cover):NPM-D3 […]
01
Dec
Dec
Alarm Display: A.C92 Alarm Name: Encoder Communications Timer Error Situation at Alarm Occurrence: Occurred when the control power supply was turned ON or during operation. Cause: Noise interference occurred on the signal line from the encoder. Corrective Actions: Take a measure against noise for the encoder wiring. Cause: Excessive vibration and shocks were applied to […]
30
Nov
Nov
Alarm Display: A.C90 A.C91 Alarm Name: Encoder Communications Error & Encoder Communications Position Data Error Situation at Alarm Occurrence: Occurred when the control power supply was turned ON or during operation. Cause: The encoder wiring and the contact are incorrect. Corrective Actions: Correct the encoder wiring. Cause: Noise interference occurred due to incorrect encoder cable […]
26
Nov
Nov
Error Code: 202 Error Text: Fail to start transport for error recovery. Description: An attempt to start the transport during an error recovery action failed. Cause: No servo power present. Solution: Switch on servo power. Error Code: 203 Error Text: Unknown warning Description: The warning is not specified yet. Solution: Report error to your service […]
23
Nov
Nov
Fujitrax Verifier issues parts out warnings based upon the user specified settings. When a parts out warning occurs, the operator has time to get a new reel, set it on a feeder, and perform a quick verify. Once these steps are performed, the feeder is set in the module in which the warning was issued […]
Alarm Display: A.C80 Alarm Name: Absolute Encoder Clear Error and Multi turn Limit Setting Error 1. Situation at Alarm Occurrence: Occurred when the control power supply was turned ON. 2. Situation at Alarm Occurrence: Occurred when an encoder alarm was cleared and reset. Cause: An encoder fault occurred. Corrective Actions: Replace the servomotor. Cause: A […]
18
Nov
Nov
1. Adjust the wire fixing position. Jig: AA87800 2. Lift the lever and insert the feeder to a jig. 3. Loosen the jig lever and push against to the position. And fix the lever. 4. Loosen the bolt on the support that is fixing the wire. 5. Rotate the support pin where it just about […]
11
Nov
Nov
#1. P/N: FC30-001037A | Part Name: Plate Pcb Guide Fix Waiting 1 (Left To Right) | Qty: 1 #1. P/N: FC30-001038A | Part Name: Pcb Guide Fix Waiting 2 (Right To Left) | Qty: 1 #2. P/N: FC30-001046B | Part Name: Plate Pcb Guide Rear Move R (Left To Right) | Qty: 1 #2. P/N: […]
Alarm Display: A.C10 Alarm Name: Servo Overrun Detected Situation at Alarm Occurrence: Occurred when the control power supply was turned ON. Cause: A SERVOPACK board fault occurredCorrective Actions: Replace the SERVOPACK Situation at Alarm Occurrence: Occurred when the servo was ON or a reference was input. Cause: The order of phase-U, -V, and -W in […]