With the NXT, it is not necessary to generate recipes in order to transmit the job to the machine. Reports are only generated during the recipe generation process. Therefore, in order to view reports, it is necessary to generate recipes. If data in the job has been changed that needs to be reflected in a… Continue reading about Generating Reports on FUJI NXT Scalable Placement Platform
Category Archives: SMT Machines MRO
The control board (reader control board assy) controls the ID reader boards. Up to 3 reader boards can be used with one control board. The control board also sends information obtained with the reader boards to the controller in the main machine (surface mounter). Hooking up the connectors The wire harness from the ID reader… Continue reading about Yamaha Assembleon CLi Interface Control Board And Status Display
When using CLi feeder exchange carriages, you must set their own ID as explained below. A list of ID settings is also shown. 1. Disconnect the feeder exchange carriage from the surface mounter. 2. Remove the front cover. Using a Phillips (+) screwdriver, remove the four screws securing the front cover (with a clear, plastic… Continue reading about Setting The ID For Yamaha Assembleon CLi Feeder Exchange Carriages
Action: Check that air pressure drops down below the standard values. Error Code: $2001 | Symptom and Cause: Can’t move up the back up table (BUT). Backup table(BUT) fails to move up. Error Code: $2002 | Symptom and Cause: Can’t move down the back up table (BUT). Backup table(BUT) fails to move down. Error Code:… Continue reading about Defined Fault On Module: Conveyor Part (Part No.1) of Samsung CP40 Pick And Place Machine
Proper nozzle setup is essential to success The first troubleshooting step is ensuring the proper nozzle / setup is being used. This is one of the easiest steps and results in the fastest improvements. Pick nozzles and process parameters for SMDs have been developed for many years. The softer silicone dome of a SMT LED… Continue reading about SMT LED Light Emitting Diode Vacuum Nozzles Is The Key Items To Help Reduce Mis-Pick Rates
Signal monitor display LED display Display: OPERATION Display: Green Function: Power display Lighting conditions: Power supply is inputted. Display: ALARM Display: Red Function: Alarm display Lighting conditions: Protective function is activated. Alarm contents Number of flickering: 1 Function: Protection from overheat Lighting conditions: The temperature of the radiator within the driver reaches approx. 85-degrees centigrade… Continue reading about Alarm List for the Stepping Motor ‘alpha’ STEP AS Series on Sony SI-F209
LED SMT Placement • LEDs sometimes require specific process parameters for the best pick and place performance. • This is due to the dome material and unbalanced weight distribution of some types of LED component. • Vendor support and knowledge is typically needed to handle the LEDs and meet high-speed, high yield SMT manufacturing process… Continue reading about Light Emitting Diode LED SMT Placement and Typical SMD v.s. LED SMD
1. Action: Drive a motor to all directions with Jog Key in order to check the motor for proper operation. Error code: $1A10 | Symptom and Cause: Timeout while homing (X axis error) Fails to find out position of Home of motor within limited time. Error code: $1A20 | Symptom and Cause: Timeout while homing… Continue reading about Defined Fault On Module: Motor Part of Samsung CP40 Pick And Place Machine
Module: X-Y Axis Part 1. Action: Drive the motor associated to opposite direction with Jog Key so as to go out of limit position. Error Code: $13D3 Symptom and Cause: Driving part of Z-axis motor is reached to software limit of negative(-) direction select 2. Action: When using System ANC, be sure to teach again… Continue reading about Defined Fault On Module: X-Y Axis Part( Part No.2) of Samsung CP40 Pick And Place Machine
Module: X-Y Axis Part, Part No.1 1. Action: Check Nozzle Data with command of in MMI and then input the correct data. Error Code: $0100 Symptom and Cause: Invalid nozzle length Invalid nozzle length value among Nozzle data.(0 value is inputted.) 2. Action: Drive the motor associated to opposite direction with Jog Key so as… Continue reading about Defined Fault On Module: X-Y Axis Part (Part no.1) of Samsung CP40 Pick And Place Machine