Module: EMG(Emergency) Error Code: $0001 Symptom and Cause: Emergency switch is pressed. Action: Release EMG(Emergency) Switch pressed. Error Code: $0021 Symptom and Cause: Front door is opened Error occurred when trying to operate system when front door is open. Action: Close a front door of system and then operate it. Error Code: $0022 Symptom and… Continue reading about Defined Fault On Module: EMG(Emergency) of Samsung CP40 Pick & Place Machine
Category Archives: SMT Machines MRO
1: When the nozzle station has not been selected, components cannot be recognized via the fixed camera. (For calibration) 2: The rear feeders for the types A and C are fixed feeders. Therefore, the batch exchange cart cannot be used. 3: The chip thickness sensor is available only when the head camera is supported.
The BM221/231 is classified into the following 5 types according to the configuration of the rear feeder. Type A (BM221/BM231) Rear: Twin tray + feeder + 2D sensor (Standard) + 3D sensor (Option) + Head camera (Option) + Nozzle station (Standard) + High-speed transfer unit(Option) Type B (BM221) No-rear feeder + Head camera (Standard) +… Continue reading about Unit Variations on the Rear Feeder For Panasonic Modular Placement Machine BM221 NM-EJM8B BM231 NM-EJM1C
Model No. BM221 NM-EJM8B BM231 NM-EJM1C A critical volume of electricity is fed to the following parts in the interior and periphery of the machine. Interior X,Y-axis AC servomotor driver: 200V AC X,Y-axis regeneration unit: 200V AC S-axis AC servomotor driver: 200V AC R-axis AC servomotor driver (Option): 200V AC SSR: 100V AC Main controller:… Continue reading about Precautions Related to Live Parts On Panasonic Modular Placement Machine BM231 BM221
After balancing the line, the parts need to be distributed to the different modules and the sequences for each module need to be arranged in the optimum order to minimize cycle time. The optimizer is used to arrange the sequences in the best order. In addition to the optimizer within Job Builder, there is another… Continue reading about Optimizing of Job Builder On Fuji NXT Scalable Placement Programming
Observe the following precautions to use the CLi interface safely and correctly. Do not apply strong shocks or impacts to the ID reader section (black plastic section) The ID reader board is protected by the ID reader cover, but might be damaged by strong shocks or impacts applied to the cover. Use caution when handling… Continue reading about Handling precautions of KNS Yamaha Assembleon CLi Interface
1. X-Y Positioning System The X-Y positioning system locates the printed circuit board under the insertion tooling and may be equipped with a rotary indexing table that indexes in 90° increments, from 0° to 360° in a clockwise rotation. When the machine is configured with automatic board handling, the table can rotate a full 180°… Continue reading about UIC Radial 8XT Dual Span & Triple Span Radial Sequencer/Inserters Machine Mechanical System
Insertion Machine Division Product Line: Radial 8XT Dual Span & Triple Span Radial Sequencer / Inserters 1. With Manual Load (Shown with In-Line Sequencer): Constant, High-Speed Radial Component Insertion VME-Based Machine Controller with Embedded P.C. Universal’s IM-UPS Menu-Driven Graphical User Interface Universal’s Positive Axis Control (PAC) Servo Drive Technology Uninterruptable Power Supply, with Battery Back-Up… Continue reading about General Specification, Introduction and Functional Description of Universal GS-403-03
Line balance is performed to balance the workload of each machine as much as possible. Due to the unique nature of putting multiple NXT bases together to create one large NXT machine, the concept of line balancing has greatly changed for lines with only NXT bases. For line with only NXT bases made up into… Continue reading about Line Balancing on Job Builder of FUJI NXT Programming
Error Code:200 Error Text: Unknown error detected. Description: The occurred error is unknown to the system. Cause: Mismatch between controllers or software layers. Solution: Report error to your service representative. Make a logdisk as described in the Service Manual. Error Code:201 Error Text: Illegal recovery action. Description: Requested operation failed because specified order does not… Continue reading about Error Code: 200 / 201 on KNS Philips Assembleon ACM