#1. P/N: AM03-009042A | Part name: Assy Cover-Dt Vp Top Cover Sub Assy | Qty: 1 | Old P/N: AM03-006021A #2. P/N: FC15-001584B | Part name: Cover-Dt Vp Top Cover Center | Qty: 1 | Old P/N: FC15-001073A FC15-001584A #3. P/N: FC09-002933B | Part name: Bracket-Dt Cover Bkt Y | Qty: 2 | Old P/N:… Continue reading about Cover(2/3) On Hanwha Techwin Excellent Modular EXCEN PRO (D) (M) (L) SMT Component Placer
Category Archives: SMT Machines MRO
#16. P/N: N610041187AA | Part name: Head Camera:NPM | Qty: 1 #17. P/N: N610052706AB | Part name: LED Lighting Unit:NPM | Qty: 1 #18. P/N: N610161110AA | Part name: Head Option Driving Unit:NPM-D3 | Qty: 1 #19. P/N: N610160758AA | Part name: Whole Cover:NPM-D3 | Qty: 1 #20. P/N: N610162273AA | Part name: Label(Whole Cover):NPM-D3… Continue reading about Kit Layout 3 & 4 on Panasonic Production Modular NPM-D3 SMT Pick and Place Machine
Alarm Display: A.C92 Alarm Name: Encoder Communications Timer Error Situation at Alarm Occurrence: Occurred when the control power supply was turned ON or during operation. Cause: Noise interference occurred on the signal line from the encoder. Corrective Actions: Take a measure against noise for the encoder wiring. Cause: Excessive vibration and shocks were applied to… Continue reading about Alarm Display: A.C92. Alarm Name: Encoder Communications Timer Error on Sony SI-F209 Electronic Part Mounter
Alarm Display: A.C90 A.C91 Alarm Name: Encoder Communications Error & Encoder Communications Position Data Error Situation at Alarm Occurrence: Occurred when the control power supply was turned ON or during operation. Cause: The encoder wiring and the contact are incorrect. Corrective Actions: Correct the encoder wiring. Cause: Noise interference occurred due to incorrect encoder cable… Continue reading about Alarm Display: A.C90 A.C91. Alarm Name: Encoder Communications Error & Encoder Communications Position Data Error on Sony SI-F209 Electronic Part Mounter
Error Code: 202 Error Text: Fail to start transport for error recovery. Description: An attempt to start the transport during an error recovery action failed. Cause: No servo power present. Solution: Switch on servo power. Error Code: 203 Error Text: Unknown warning Description: The warning is not specified yet. Solution: Report error to your service… Continue reading about Error Code: 202, 203, 204, 205, 206 on KNS Philips Assembleon ACM SMT Machine
Fujitrax Verifier issues parts out warnings based upon the user specified settings. When a parts out warning occurs, the operator has time to get a new reel, set it on a feeder, and perform a quick verify. Once these steps are performed, the feeder is set in the module in which the warning was issued… Continue reading about 8.7.1 Replacing Feeders Using Dynamic Alternate Feeders for 8.7 Resupplying Parts During Production of 8. Fujitrax Verifier on FUJI NXT
Alarm Display: A.C80 Alarm Name: Absolute Encoder Clear Error and Multi turn Limit Setting Error 1. Situation at Alarm Occurrence: Occurred when the control power supply was turned ON. 2. Situation at Alarm Occurrence: Occurred when an encoder alarm was cleared and reset. Cause: An encoder fault occurred. Corrective Actions: Replace the servomotor. Cause: A… Continue reading about Alarm Display: A.C80. Alarm Name: Absolute Encoder Clear Error and Multi turn Limit Setting Error on Sony SI-F209 Electronic Part Mounter
1. Adjust the wire fixing position. Jig: AA87800 2. Lift the lever and insert the feeder to a jig. 3. Loosen the jig lever and push against to the position. And fix the lever. 4. Loosen the bolt on the support that is fixing the wire. 5. Rotate the support pin where it just about… Continue reading about Adjusting the Lever and Clamper of FUJI Intelligent SMT Feeder
#1. P/N: FC30-001037A | Part Name: Plate Pcb Guide Fix Waiting 1 (Left To Right) | Qty: 1 #1. P/N: FC30-001038A | Part Name: Pcb Guide Fix Waiting 2 (Right To Left) | Qty: 1 #2. P/N: FC30-001046B | Part Name: Plate Pcb Guide Rear Move R (Left To Right) | Qty: 1 #2. P/N:… Continue reading about Conveyor(4/7) Rear Move On Hanwha Techwin Excellent Modular EXCEN PRO (D) (M) (L) SMT Component Placer
Alarm Display: A.C10 Alarm Name: Servo Overrun Detected Situation at Alarm Occurrence: Occurred when the control power supply was turned ON. Cause: A SERVOPACK board fault occurredCorrective Actions: Replace the SERVOPACK Situation at Alarm Occurrence: Occurred when the servo was ON or a reference was input. Cause: The order of phase-U, -V, and -W in… Continue reading about Alarm Display: A.C10. Alarm Name: Servo Overrun Detected on Sony SI-F209 Electronic Part Mounter