The machine is equipped with two cameras, each camera being used to process different parts. A high resolution narrow view camera is used to acquire images of small components such as 0603s (0201s), 1005s (0402s) and super small SOTs, and a wide view camera is used for components such as SOICs, PLCCs and CSPs. The… Continue reading about Camera Unit of Fuji CP-842E CP-842ME High-Speed Chip Placer
Category Archives: SMT Machines MRO
Nozzles are attached to each head, with the following nozzles being available for the CP-842E/842ME. Plate: φ8 #Nozzle diametre: φ0.27 | Nozzle code: For 0402 (01005) parts #Nozzle diametre: φ0.4 | Nozzle code: R08-004 #Nozzle diametre: φ0.4 | Nozzle code: R08-004 Length: 4.5 mm #Nozzle diametre: φ0.4 | Nozzle code: R08-004T Tapered nozzle #Nozzle diametre:… Continue reading about SMT Nozzles of Fuji CP-842E CP842ME High-Speed Chip Placer
The function of each of the 16 stations on the turret are detailed below. #1. Pick-up part from the device table (Adjustable pick-up height) #2. Large parts pick-up confirmation. Pθ: Placement angle prerotation in 90° angles #3. Idle #4. Idle #5. Part inspection #6. Measurement of parts height #7. Idle #8. Fθ: Fine placement angle… Continue reading about Placing Head of Fuji CP-842E CP842ME Chipshooter
You will need the following tools and consumables for maintaining the sleeves. Laboratory gloves Ethyl alcohol Lint-free cloths Cottonwool buds Microtips (cottonwool buds) drill bit 1.1 mm drill bit 1.4 mm Fin Grease spray grease Suction plates SIPLACE sleeves maintenance: 6-segment C&P head (item no.: 00375674-01) 12-segment C&P head (item no.: 00375681-01). 1. Check the… Continue reading about Maintain the sleeves of ASM SIPLACE X-Series Preventive Maintenance
The travel range of the X- and Y-axes will be determined automatically with Sitest program. That means, during calibration of travel range the axis run as far as possible into its minimum and/or maximum position. The axis position is taken when the limit-BERO’s switch. Corresponding the description (see below) a safety space infront of the… Continue reading about Travel range and velocity monitoring X- and Y- Axes on the Siemens Siplace X2
The MVME162P4 is shipped from the factory with the SERIAL PORT 1/CONSOLE header configured for asynchronous communications (i.e., jumpers removed). To select synchronous communications for the SERIAL PORT 1/CONSOLE connection, install jumpers across pins 1-2 and pins 3-4. Note: Model Number: MVME162P-344SE, Characteristics: 32MHz 68040, 16MB SDRAM, 2 SIO, 4 DMA IP, SCSI/Ethernet is used… Continue reading about Serial Port 1/Console Clock (J16) on Motorola MVME162P4 VME Embedded Controller
Error Code: 114 Error Text: Duplicate order name found Description: The name entered for the order Cause: already exists. Solution: A unique name is required. Use a different order name. Error Code: 115 Error Text: Order has already completed Description: The order can not be executed because the complete number of boards is already executed…. Continue reading about Error Code: 114 / 115 /116 on KNS Philips Assembleon ACM
Alarm Display: A.023 Alarm Name: Parameter Password Error Situation at Alarm Occurrence: Occurred when the control power supply was turned ON. Cause: A SERVOPACK board fault occurred. Corrective Actions: Replace the SERVOPACK.
Error Code: 109 Error Text: Order creation failed Description:The system cannot create the order. Cause: Incorrect data entered. Solution: Check if all entered parameters are correct. Error Code:110 Error Text: Maximum number of orders exceeded Description:The maximum number of orders that the system can handle, has been reached. Cause: Too many orders in the system…. Continue reading about Error Code: 109 / 110 / 111 / 112 on KNS Philips Assembleon ACM
Port B of the MVME162P4 Z85230 serial communications controller is configurable via a serial interface module (SIM) that is installed at connector J15 on the board. Five serial interface modules are available: EIA-232-D (DCE and DTE) EIA-530 (DCE and DTE) EIA-485/EIA-422 (DCE or DTE) You can change Port B from an EIA-232-D to an EIA-530… Continue reading about SIM Selection for Serial Port B (J15) on Motorola MVME162P4 VME Embedded Controller