SMTBOX – THT / SMT Machines Feeders, Nozzles and Spare Parts Supplier

The Jig Lisf of Sony SI-F209 Odd And Fine Components Placer

#1 Calibration plate jig (1 set) | Uses: Calibration | Remarks: Calibration Calibration plate: 4-721-259-02 / Positioning pin: 4-721-288-01 / Retaining plate C: 4-721-598-01

#2 Locating pin positioning jig | P/N: A-8417-278-A | Uses: Positioning of locating pin

#3 Jig positioning pin | P/N: A-8417-273-A | Uses: Positioning of calibration plate / locating pin

#4 Base point jig | P/N: A-8417-271-A | Uses: Calibration of PWB camera

#5 Conveyor sensor jig | P/N: A-1087-540-A | Uses: Adjustment of Conveyor sensor height

#6 Jig Nozzle 1 | P/N: A-8417-266-A | Uses: Adjustment of NS-axis, R-axis origin positions, calibration of vacuum

#7 Jig Nozzle 2 | P/N: A-8417-267-A | Uses: Adjustment of NS-axis origin position

#8 Jig Nozzle 3 | P/N: A-8417-268-A | Uses: Adjustment of H-axis and M-axis origin positions, Calibration in general

#9 Jig Nozzle 4 | P/N: A-8417-269-A | Uses: Pickup position Setup

#10 Jig Nozzle 5 | P/N: A-8417-585-A | Uses: Parts camera calibration / Fixed camera calibration

#11 Feed adjusting jig | Uses: Adjustment of F-axis feed roller Y-direction position / Adjustment of F-axis feed roller X-direction position / Adjustment of F-axis feed roller height / Position adjustment for F-axis feeder backward detect sensor / Adjustment of F-axis feed roller origin sensor dog / Adjustment of cassette float sensor height Remarks: Jig base Assembly: A-8417-188-A / Positioning block: 4-721-292-01

#12 Part feed height jig | P/N: 4-721-291-01 | Uses: Adjustment of F-axis feed roller height / Position adjustment for F-axis feeder backward detect sensor / Adjustment of F-axis feed roller origin sensor dog

#13 F-axis return block | P/N: 4-712-290-01 | Uses: Adjustment of F-axis feed roller origin sensor dog

#14 Cassette float sensor adjusting jig | Uses: Adjustment of cassette float sensor position

#15 Camera calibration plate (QFP) | Uses: Parts camera calibration / Fixed camera calibration Remarks: Jig chip: 4-722-722-01 / Jig chip mask: 4-722-723-01 / (A jig plate needs adhesion of a jig chip / and a jig chip mask.)

#16 Camera calibration plate (large) | P/N: 4-721-579-01 | Remarks: Parts camera calibration

#17 Transmission brightness calibration jig | P/N: A-8417-392-A | Remarks: Parts camera back light calibration

#18 Transmission nozzle jig | P/N: A-8417-391-A | Remarks: Parts camera back light calibration

#19 Light calibration jig (Reflection angle: 0, 15) | P/N: 4-721-584-01 | Remarks: Calibration of part camera light (Reflection angle: 0, 15)

#20 Light calibration jig (Reflection angle: 75) | P/N: A-8417-274-A | Remarks: Calibration of part camera light (Reflection angle: 75)

#21 Fixed camera light calibration jig | P/N: 4-721-578-02 | Remarks: Fixed Camera Upper Light Calibration / Fixed Camera Middle Light Calibration / Fixed Camera Lower Light Calibration / AUX Camera Coaxial Light Calibration

#22 Tray pickup origin position adjusting jig | P/N: A-8417-270-A | Uses: Adjustment of S-axis pickup origin position

#23 S-axis jig palette | P/N: 4-720-768-01 | Uses: V-axis setup / S-axis setup

#24 Tension block adjusting jig 1 | P/N: 4-721-285-01 | Uses: Adjustment of F-axis belt | Remarks: 2-C3x14, C4x15

#25 Tension block adjusting jig 2 | P/N: A-1094-708-A | Uses: Adjustment of M-axis belt tension | Remarks: 2-C4x25

#26 Pickup point jig | P/N: A-8417-184-A | Uses: Teaching of pickup point

#27 Tension block adjusting jig 3 | P/N: A-1094-706-A | Uses: Adjustment of H-axis belt tension

#28 Servo adjusting jig (1 set) | Uses: Adjustment of servo | Remarks: Reverse run cable, 232C cable

#29 Cassette bank changer roller height adjusting jig | P/N: 4-721-587-01 | Uses: Adjustment of cassette bank changer up cylinder

#30 Cassette bank changer positioning jigs R and L | Uses: Adjustment of table mounting position | Remarks: R: 4-721-301-11 / L: 4-721-301-01

#31 Cassette bank changer adjusting blocks | P/N: 4-721-586-01 | Uses: Measurement of table tilt

#32 Tension meter | P/N: 1-520-542-11 | Uses: Measurement of each shaft belt tension | Remarks: U-507

#33 Spline nut removing jig | Uses: Removal of C-head spline nut

#34 Torque driver (N50LTDK) | Uses: Measurement range:100 to 500 cN.m | Remarks: Bit provided

#35 Torque driver (PTD60CN) | Uses: Measurement range: 10 to 60 cN.m | Remarks: Bit provided

#36 Cut L wrench | Uses: Replacement of C-head unit

#37 Thickness gauge | Uses: Calibration

#38 Laser type shutter float sensor adjusting jig (OPTION) | P/N: A-8417-189-A | Uses: Adjustment of laser type shutter float sensor

#39 Flow meter (1 set) | P/N: A-8417-279-A | Uses: Measurement of mounted blow flow rate | Remarks: Display unit, instrumentation unit, power cable tube

#40 Pressure gauge | P/N: 1-520-535-12 | Remarks: Measurement of vacuum

#41 Part Abandonment conveyor jig (OPTION) | P/N: A-8417-472-A | Remarks: Part Abandonment conveyor setup

#42 U-nut wrench | P/N: 2-515-522-01 | Remarks: Tightening of feed U-nut

#43 Y axis bearing draw-out jig | P/N: 2-186-544-01 | Remarks: Removal of Y axis ball bearing

#44 Y axis bearing fixing jig | P/N: 2-186-546-01 | Remarks: For fixing Y axis bearing

#45 Y axis bearing support jig | P/N: 2-186-545-01 | Remarks: Installation of Y axis ball bearing

#46 Y axis ball screw clamp | Uses: Y axis ball screw clamp | Remarks: Lever: 2-186-547-01 / Block: 2-186-548-01

#47 Bearing puller | Uses: Ball screw bearing removal

#48 C-head assembly stand | P/N: A-8417-276-A | Uses: C-head assembling

#49 Jig box and case (1 set)

#50 Conveyor ball screw clamp | Uses: Conveyor ball screw clamp | Remarks: Block: 2-186-550-01 / Lever: 2-186-549-01 / 2-C4 x 15

#51 Pulley fixing lever | P/N: X-2025-186-1 | Uses: Fixing of conveyer pulley

Exit mobile version